Metrohm Thin-Layer cell Manual de usuario

IC EquipmentThin-Layer cellManual8.110.8020EN

3.1 Inserting the working electrode￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭4￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell3 InstallationCautionNever switch on the measuring cell

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 InstallationIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭53.2 Inserting the reference electrodeThe measuring cell is supplied without

3.2 Inserting the reference electrode￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭6￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell12453Figure 2 Ag/AgCl reference electrode (6.1257.720)

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 InstallationIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭7 2Unscrew the fastening screw from the reference electrode holder.Push the fa

3.3 Connecting the detector capillaries￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭8￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell3.3 Connecting the detector capillariesThe amperome

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 InstallationIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭9 3Connect the cell outputUse a pressure screw (6.2744.014) to fasten a 1–1.5

3.4 Connecting the electrode connection cables￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭10￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell3.4 Connecting the electrode connection cab

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭3 InstallationIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭11 3Plug in the angled plug of the auxiliary electrode connection cable(labele

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭12￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell4 Start-upThe measuring cell must be put into operation together with the ampero-metric d

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Operation and maintenanceIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭135 Operation and maintenance5.1 OperationThe measuring cell is

5.2 Maintenance￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭14￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell 1Unscrew the pressure screw (1-4) on the base part of the cell andremove i

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Operation and maintenanceIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭15 2Unscrew the fastening screw for the reference electrode and r

5.2 Maintenance￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭16￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cellTo disassemble the measuring cell, you need a 2.5 mm hexagon key.12345Figur

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Operation and maintenanceIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭17Replace the spacer as follows:Replacing the spacerPrerequisites

5.2 Maintenance￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭18￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell￭ The working electrode has been removed from the measuring cell. 1NoteWhen

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭5 Operation and maintenanceIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭19Inserting the reference electrode 1Reinsert the reference elect

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭20￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell6 Technical specificationsStructure Flow cell with working, reference and auxiliary elect

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭7 AccessoriesIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭217 Accessories7.1 IC equipment Thin-Layer cell: without electrodes Qty. Orde

7.1 IC equipment Thin-Layer cell: without electrodes￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭22￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cellQty. Order no. Description1 6.2621.140

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭IndexIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭23IndexAAccessories ... 21Auxiliary electrodeCleaning ...

Metrohm AGCH-9100 HerisauSwitzerlandPhone +41 71 353 85 85Fax +41 71 353 89 [email protected] EquipmentThin-Layer cell6.5337.200Manu

TeachwareMetrohm AGCH-9100 [email protected] documentation is protected by copyright. All rights reserved.Although all the information

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭Table of contentsIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭IIITable of contents1 Introduction 11.1 Description ...

Table of figures￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭IV￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cellTable of figuresFigure 1 Thin-Layer cell – Parts and connectors ...

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭1 IntroductionIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭11 Introduction1.1 DescriptionThe Thin-Layer cell is used for amperometric d

1.2 About the documentation￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2￭￭￭￭￭￭￭￭IC Equipment Thin-Layer cell1.2.2 Symbols and conventionsThe following symbols and formatti

￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭2 OverviewIC Equipment Thin-Layer cell￭￭￭￭￭￭￭￭32 Overview64317891052Figure 1 Thin-Layer cell – Parts and connectors1Fastening s